Stereo Tool :: Stereo Tool 9.24 BETA

I have here a supplement to the topic phase delay. I took another close look at the behavior. For this I chose the standard preset Dutch chocolate mousse. I switched the phase delay on and off in this preset. To see the whole thing a bit better I uploaded a Gif here.

In the first seconds in the phase delay deactivated. As you can see in the frequency spectrum everything looks as usual. But as soon as I switch on the phase delay interference signals are added. Even far above 16 Khz, where there is no signal at all in the original. This interfering signal wobbles back and forth a bit. The problem with this signal is that if you amplify it by the other dynamic processors and continue to compress it, you can hear it very clearly at the end.

Is this now a misadjustment by me, or is it really a bug in the phase delay? So with my preset I can adjust the behavior as well.

Author:	Bojcha [ Sun Mar 17, 2019 5:38 pm ]
Post subject:	Re: Stereo Tool 9.24 BETA
Great, now sync refuses to even do something.

Author:	near05 [ Mon Mar 18, 2019 6:57 pm ]
Post subject:	Re: Stereo Tool 9.24 BETA
I have here a supplement to the topic phase delay. I took another close look at the behavior. For this I chose the standard preset Dutch chocolate mousse. I switched the phase delay on and off in this preset. To see the whole thing a bit better I uploaded a Gif here. In the first seconds in the phase delay deactivated. As you can see in the frequency spectrum everything looks as usual. But as soon as I switch on the phase delay interference signals are added. Even far above 16 Khz, where there is no signal at all in the original. This interfering signal wobbles back and forth a bit. The problem with this signal is that if you amplify it by the other dynamic processors and continue to compress it, you can hear it very clearly at the end. Is this now a misadjustment by me, or is it really a bug in the phase delay? So with my preset I can adjust the behavior as well.

Author:	hvz [ Mon Mar 18, 2019 7:15 pm ]
Post subject:	Re: Stereo Tool 9.24 BETA
Quote: I have here a supplement to the topic phase delay. I took another close look at the behavior. For this I chose the standard preset Dutch chocolate mousse. I switched the phase delay on and off in this preset. To see the whole thing a bit better I uploaded a Gif here. In the first seconds in the phase delay deactivated. As you can see in the frequency spectrum everything looks as usual. But as soon as I switch on the phase delay interference signals are added. Even far above 16 Khz, where there is no signal at all in the original. This interfering signal wobbles back and forth a bit. The problem with this signal is that if you amplify it by the other dynamic processors and continue to compress it, you can hear it very clearly at the end. Is this now a misadjustment by me, or is it really a bug in the phase delay? So with my preset I can adjust the behavior as well. I haven't had time to look in detail yet but I don't see any frequencies pop up here that weren't there in the original. Will do some more checks later...

Author:	hvz [ Wed Mar 20, 2019 2:55 pm ]
Post subject:	Re: Stereo Tool 9.24 BETA
Version 011 is uploaded (stand alone only). Now with built-in streaming support (for now: IceCast, MP3 via LAME, ogg/Vorbis).

Author:	Cleiton [ Wed Mar 20, 2019 6:52 pm ]
Post subject:	Re: Stereo Tool 9.24 BETA
Quote: Version 011 is uploaded (stand alone only). Now with built-in streaming support (for now: IceCast, MP3 via LAME, ogg/Vorbis). Hi Hans, I have downloaded latest 011 and was installed normally! You are sure was uploaded correct setup build number? Latest modification in the file (09 March) Installed 011 but still shows build number 009 in the top corner Best Regards.

Stereo Tool https://forums.stereotool.com/

Stereo Tool 9.24 BETA https://forums.stereotool.com/viewtopic.php?t=25905	Page 4 of 17

Author:	hvz [ Wed Mar 20, 2019 7:27 pm ]
Post subject:	Re: Stereo Tool 9.24 BETA
Hi, no idea what that could be, I just downloaded them from the site and I'm getting 011 for both stand alone builds. Edit: I did change some things in the installer (to add some DLL's) - maybe something is going wrong with the install?

Author:	Cleiton [ Wed Mar 20, 2019 7:39 pm ]
Post subject:	Re: Stereo Tool 9.24 BETA
Hey Hans, Now, installed in a different directory, continues as 009 and open/start site as the old setup does I will try later to install in a other machine.

Author:	Cleiton [ Wed Mar 20, 2019 7:48 pm ]
Post subject:	Re: Stereo Tool 9.24 BETA
I have extracted manually StereoTool.exe inside of setup exe... its the same file inside.

Author:	drbusy [ Wed Mar 20, 2019 8:48 pm ]
Post subject:	Re: Stereo Tool 9.24 BETA
Hans, is it possible to add more than 5 same freq in AF B method multiple lists? Option with more windows? Like 7 same freq? Hope it's clear.

Author:	Cleiton [ Wed Mar 20, 2019 11:38 pm ]
Post subject:	Re: Stereo Tool 9.24 BETA
Quote: Hi, no idea what that could be, I just downloaded them from the site and I'm getting 011 for both stand alone builds. Edit: I did change some things in the installer (to add some DLL's) - maybe something is going wrong with the install? Hi Hans, installed in other Windows machine. 011 installed sucessfully! I don't know where is wrong in the previous machine, thats weird!

Page 4 of 17	All times are UTC+02:00
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/