| Stereo Tool https://forums.stereotool.com/ |
|
| Stereo Tool 9.41 BETA https://forums.stereotool.com/viewtopic.php?t=28247 |
Page 2 of 3 |
| Author: | MrKlorox [ Tue Apr 28, 2020 5:49 pm ] |
| Post subject: | Re: Stereo Tool 9.41 BETA |
I was going to post about an issue that was in beta 9 and earlier, but you seemed to have fixed it in this version 11. I'll still post what it was in case it pops back up. Basically, right clicking the tray icon a second time to disable the bypass works, but the icon didn't change back to normal. Attachment: st-tray.png [ 17.76 KiB | Viewed 8006 times ] |
|
| Author: | Bojcha [ Wed Apr 29, 2020 4:08 am ] |
| Post subject: | Re: Stereo Tool 9.41 BETA |
BEQ is also 1st band schained with HPF. What if i have 2 tight bass bands.. |
|
| Author: | EliteData [ Thu Apr 30, 2020 3:53 pm ] |
| Post subject: | Re: Stereo Tool 9.41 BETA |
i mentioned this before but im going to mention it again. could the author of ST please implement peak-hold metering ? this would be useful especially for the clipping level (advanced clipper), i could then see the maximum amount of clip level and adjust accordingly (clipping that occurs more than -6dB is audible distortion). perhaps there are other areas of ST where peak-hold metering is useful as well. thanks ! |
|
| Author: | hvz [ Sat May 02, 2020 12:39 pm ] |
| Post subject: | Re: Stereo Tool 9.41 BETA |
@EliteData: Definitely something we should put in the new GUI. BETA016 is posted. Lots of bass clipper improvements, and Release Hold now works on non-constant speeds as well. |
|
| Author: | hvz [ Sat May 02, 2020 12:40 pm ] |
| Post subject: | Re: Stereo Tool 9.41 BETA |
Quote:
BEQ is also 1st band schained with HPF. What if i have 2 tight bass bands..
Are you really using a band split lower than 30 Hz or so? Or is your HPF set higher?
|
|
| Author: | Bojcha [ Sat May 02, 2020 3:57 pm ] |
| Post subject: | Re: Stereo Tool 9.41 BETA |
Quote: Quote:
BEQ is also 1st band schained with HPF. What if i have 2 tight bass bands..
Are you really using a band split lower than 30 Hz or so? Or is your HPF set higher?
And when its about HPF, I still think that there was nothing wrong with old HPF and it's better than new, it just needed to be sidechained like new wich was and is, good idea. Bass at 100% quality - still artifacts and some pre-ring. Still needed atleast 130%. Zero fix for "limit" mode, huge pre rings and way different/worse bass clipping from ABDP. |
|
| Author: | cbs1 [ Sun May 03, 2020 3:13 pm ] |
| Post subject: | Re: Stereo Tool 9.41 BETA |
HI HANS what about GRAIN in advanced clipper section bcs in this way we miss the freq above 9khz....we must go there to check in to have above freq....is way to have it in in default settings ON??? regards P.S AFTER SHORT TIME THERE IS NO PROBLEM....SORRY |
|
| Author: | hvz [ Sun May 03, 2020 11:15 pm ] |
| Post subject: | Re: Stereo Tool 9.41 BETA |
Quote:
HI
Hi, I still have never seen this issue. I'm unable to reproduce it. If you have any more info please let me know.
HANS what about GRAIN in advanced clipper section bcs in this way we miss the freq above 9khz....we must go there to check in to have above freq....is way to have it in in default settings ON??? regards P.S AFTER SHORT TIME THERE IS NO PROBLEM....SORRY |
|
| Author: | RR999 [ Mon May 04, 2020 10:46 pm ] |
| Post subject: | Re: Stereo Tool 9.41 BETA |
9.41b17 on server. Example links: https://www.stereotool.com/download/ste ... 41-017.exe https://www.stereotool.com/download/ste ... 41-017.exe https://www.stereotool.com/download/dsp ... 41-017.exe |
|
| Author: | hvz [ Mon May 04, 2020 10:50 pm ] |
| Post subject: | Re: Stereo Tool 9.41 BETA |
Quote:
Some of those are still older versions, and some of them have crashes. I will post it when it's ready, which will be in a few hours.
|
|
| Page 2 of 3 | All times are UTC+02:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|