| Stereo Tool https://forums.stereotool.com/ |
|
| Greetings all https://forums.stereotool.com/viewtopic.php?t=12 |
Page 1 of 1 |
| Author: | mapleleaf [ Sun May 18, 2008 10:28 am ] |
| Post subject: | Greetings all |
First post here. First of all what am awesomme product. It sure has made life much easier as I am concerned with quality of my audio. I use SAM 4 and my music library is all wma file that are 24-bit 2-channel @96Khz. I believe that the output of audio is only as good as the input of the audio namely the source and in this case the *.wma. I woudl very much appreciate IF someone could provide a screen shot of their ST(stereo tool). This would help tremendously as an example then adjusting to meet/suit one's individual needs. I've just switched to the 3.10 beta from 2.02 after seeing that it was available. My sound card is a creative x-fi elite pro, my ASIO setting are at 64 samples. Using ST v2 was great and made the quality of my audio top-notch with SAM 4. In using 3.10 beta and loading my previous *.sts setting does require me to mkae some changes hence a screen shot would be helpful to use a a basis. Once I have made my final adjustments and of course happy with it, I will post it here for those that are using the same sound card as mine. I would also very much appreciate IF it is available a *.pdf of the help section rather than reading it online. Hans, if possible woudl you consider this. I would be most willing to help/assist you. I travel to Holland very often. Tot ziens mapleleaf wmeier@mirana.net Studio 9 |
|
| Author: | hvz [ Sun May 18, 2008 3:25 pm ] |
| Post subject: | Re: Greetings all |
Welcome Mapleleaf, Are you having a problem with the sound, or with other (eg. FM transmitter) settings? If you're switching from Stereo Tool 2.x to 3.x, the only changes that you _need_ to make are: - In the Multiband compressor, configure the first two lowest bands (they are new). You might also need to modify the 2 highest bands (their frequencies changed a bit - the volume of the highest might need to be set a bit higher, the one before that a bit lower). Note that the Clipping filter is new, you could turn it off but generally the sound improves if you leave it on. - The singleband compressor should be replaced by the final (pre-) limiter. To get an idea of settings that should give a good sound, you might check the presets. About a PDF help file: I'm still working on the help pages a bit - offering them as a PDF file is probably a very good idea, and I will look into that as soon as I've finished them. By the way - have you checked the tutorial? That should answer most of your questions - if it doesn't I have to rewrite it... See http://help.stereotool.com/tutorial.shtml Please let me know which problems you are experiencing - I will add a "switching to Stereo Tool 3.x" help page. Knowing which problems you encountered might help when writing it. |
|
| Author: | mapleleaf [ Sun May 18, 2008 8:38 pm ] |
| Post subject: | Re: Greetings all |
Hi Hans Thanks for your reply. I have it v3.10(beta) working very well with SAM 4 and my sound card. Currently broadcasting on web radio and very happy with the quality. I am streaming at 128 using accPlus which has definitive advantages over an mp3 stream. I am using Creative x-fi elite pro with v3.10beta of stereo tool. Once I am fully happy, if you wish I can here. I would be happy to volunteer to help, if needed. regards mapleleaf Studio 9 - Digital Audio at its Best http://www.studio9.mirana.net |
|
| Author: | hdmyg85 [ Mon Dec 29, 2008 9:09 am ] |
| Post subject: | Brass air fittings |
Now that is a lot of brass air fittings http://www.liangdianup.com/subpages/airfitting_1.htm there is just about every type of air fitting that you could want. Wholesale prices too. I guess these could be used as small water pipe fitting also. I used some of the parts to make my babington wvo burner. |
|
| Page 1 of 1 | All times are UTC+01:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|