idk.. here is standalone running for 29 days at transmitter site
| Stereo Tool https://forums.stereotool.com/ |
|
| Stereo Tool 7.41 https://forums.stereotool.com/viewtopic.php?t=5508 |
Page 8 of 16 |
| Author: | fario [ Wed Apr 02, 2014 7:19 pm ] |
| Post subject: | Re: Stereo Tool 7.41 |
Windows stand alone 64bit? |
|
| Author: | hvz [ Wed Apr 02, 2014 8:02 pm ] |
| Post subject: | Re: Stereo Tool 7.41 |
Quote: Windows stand alone 64bit?
Something went wrong with that build, but I have not received any complaints about it. So I thought it wasn't so important.
|
|
| Author: | Clipper [ Thu Apr 03, 2014 2:41 am ] |
| Post subject: | Re: Stereo Tool 7.41 |
What I have found with both final 7.41 and with the 7.42 Beta is that when I start ST I have no Normal Output buffer showing but this doesn't cause any problems with the Normal Output audio, it plays like there is plenty of buffer, no stuttering. When I Restart Sound Cards the buffer shows up in Green about one third the width of the buffer display. I am using Juli@ 44.1 Normal Output. Clipper |
|
| Author: | DJ-DOGGY [ Fri Apr 11, 2014 8:43 pm ] |
| Post subject: | Re: Stereo Tool 7.41 |
Why when i start ST after a period of time the memory load is reduced about a half of it. When started is about 120 000 kB and then it becomes about 52 000 kB ? This is not normal in my opinion . |
|
| Author: | hvz [ Fri Apr 11, 2014 8:53 pm ] |
| Post subject: | Re: Stereo Tool 7.41 |
Quote: Why when i start ST after a period of time the memory load is reduced about a half of it. When started is about 120 000 kB and then it becomes about 52 000 kB ? This is not normal in my opinion .
Windows might at some point decide that memory that is never used can be discarded. I'm not 100% sure, but does this happen if the pc is doing nothing at all and there is plenty of memory available, or only when you're doing other things on the same pc?
|
|
| Author: | DJ-DOGGY [ Fri Apr 11, 2014 9:12 pm ] |
| Post subject: | Re: Stereo Tool 7.41 |
I think there is a lot of memory and this happens even on fresh restart of the system . May be is the improve that you mention . Others reported too that memory is about 60 mb less? But why it start with full memory and then to cut the half of it ? You say that this improve is added back. Yes i`m not saying that this is happen because of ST, may be is my computer but, i think i see this since some versions ago. Someone else to report this too ? |
|
| Author: | Bojcha [ Fri Apr 11, 2014 10:05 pm ] |
| Post subject: | Re: Stereo Tool 7.41 |
idk.. here is standalone running for 29 days at transmitter site
|
|
| Author: | fario [ Fri Apr 11, 2014 11:17 pm ] |
| Post subject: | Re: Stereo Tool 7.41 |
Quote: Quote: Windows stand alone 64bit?
Something went wrong with that build, but I have not received any complaints about it. So I thought it wasn't so important.Yeah you are right, nothing wrong with 64bit |
|
| Author: | hvz [ Sat Apr 19, 2014 6:26 pm ] |
| Post subject: | Re: Stereo Tool 7.41 |
As you may know I've been in Las Vegas last week. and haven't done too much yet this week, but I wanted to upload a version with one fix (that has been tested the last week by someone who had this issue). Marian Windows 7 driver hangup fix: Version 7.41 caused complete system hangups on some systems running Windows 7 with a Marian Trace Alpha card with the Marian driver (and not when using other drivers such as ASIO4ALL), when using ASIO. After doing many tests in the previous weeks, the difference compared to version 7.40 that triggers this behavior appears to be that I cleaned up my code: The code that fetches new input audio from the ASIO driver and sends the new output audio to it is optimized and returns faster, and for some reason on some systems something appears to be going very wrong in the Marian driver. I'm in contact with Marian to drill down to the real cause of this, but for now, I have added a slider with which you can make this specific piece of code run slower. With this new slider set to '4' (that's the only value that has been tested so far), everything seems to work fine. I don't expect that this has any negative effects for non-Marian users (except for a slightly higher CPU load when this fix is enabled). But you can turn it off if you don't need it. If you were having this same problem with version 7.41 (I received reports about it from 3 people), you can try this new version: Windows 32 bit: Windows stand alone: http://www.stereotool.com/download/ster ... 42-011.exe |
|
| Author: | dj_szpajda [ Sat Apr 26, 2014 12:59 pm ] |
| Post subject: | Re: Stereo Tool 7.41 |
How to use at the moment ST standalone as main processor to distribute preemphasised LR output for more than 1 transmitter with hardware encoder? |
|
| Page 8 of 16 | All times are UTC+02:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|