Stereo Tool
https://forums.stereotool.com/

Stereo Tool 5.02
https://forums.stereotool.com/viewtopic.php?t=2661		 Page 64 of 99
Author:  hvz [ Sun Nov 21, 2010 11:32 pm ]
Post subject:  Re: Stereo Tool 5.02
Quote:
Highs vs. Lows 400 ??? to 800??? as default??
Deepboost fixed on Beta51? its ok to make it ON?
Yes (is that a problem?), and yes.

Very Deep Bass Distortion Protection does not work properly yet though.
Author:  Bojcha [ Mon Nov 22, 2010 12:20 am ]
Post subject:  Re: Stereo Tool 5.02
Not problem, highs vs lows, i set it to 350/750 ..

i'm have 94-96% of level (for 0-350Hz), - Then rize to = 84% - composite limiter = 106.5%
Author:  hvz [ Mon Nov 22, 2010 1:16 am ]
Post subject:  Re: Stereo Tool 5.02
Quote:
Not problem, highs vs lows, i set it to 350/750 ..

i'm have 94-96% of level (for 0-350Hz), - Then rize to = 84% - composite limiter = 106.5%
And? Does it do (= improve) anything?
Author:  Bojcha [ Mon Nov 22, 2010 1:30 am ]
Post subject:  Re: Stereo Tool 5.02
Still listening....

First i noticed that peek (before) of 100% level that cause Voice vibration till "clip lowest bass" start to react, are not more present.
DC appears to be more stable.
hard limit and composite limiter are not working for bass anymore so rest of sound is more stable.

i'm not sure .. but in last few betas.. there is much more highs.. from 10kHz and up.
I need to put last two sliders in multiband from 2.30 to 1.90 and last slider from 1.22 to 0.97
Author:  hvz [ Mon Nov 22, 2010 1:45 am ]
Post subject:  Re: Stereo Tool 5.02
Quote:
i'm not sure .. but in last few betas.. there is much more highs.. from 10kHz and up.
I need to put last two sliders in multiband from 2.30 to 1.90 and last slider from 1.22 to 0.97
That's probably because 'Allow louder highs' doesn't work properly anymore (it's on the TODO list). You have to set it lower for the same results as before. That's probably because this filter is AFTER a filter that I added that clips the highs, so the measurements that it does are off.

Rest of sound more stable = good! ("Limiting_strictness" is now set to 100% for the bass sounds). I haven't had time yet to test it, but that sounds promising. Setting 'Allow louder highs' lower also makes the sound more stable (but you'll loose some highs clarity, I think I need to replace that filter by an AGC-like thing for the highs only to maintain clarity.) I'll put that on my TODO list.
Author:  Chris [ Mon Nov 22, 2010 9:30 am ]
Post subject:  Re: Stereo Tool 5.02
Sound is more stable but Highs have nt the clarity of Beta50. the diff is small but noticeable. And you right Hans allow lowder highs not working properly.
In order to make similar highs i have to set Alow lowder highs +25000+ (+5000 before)
Bojcha is right High vs Lows are 350 to 750+
Author:  Bojcha [ Mon Nov 22, 2010 10:26 am ]
Post subject:  Re: Stereo Tool 5.02
Chris..

Try to set:

- Ignore brelow = 0.00
- Clip Lowest bass = 0.60
- Then Rize to = 0.90 and Turn ON Strict
Author:  Chris [ Mon Nov 22, 2010 11:24 am ]
Post subject:  Re: Stereo Tool 5.02
Nice Bojcha... but i notice diff on Highs clarity. small but.... :(
The diff is less if i set High vs Lows 284 - 731
Author:  Bojcha [ Mon Nov 22, 2010 11:30 am ]
Post subject:  Re: Stereo Tool 5.02
well.. your settings in multiband is like that, too much highs and very fast down/up speed.

Main question is, are you shure you broadcast at max 75khz ?
Author:  Chris [ Mon Nov 22, 2010 11:36 am ]
Post subject:  Re: Stereo Tool 5.02
Quote:
well.. your settings in multiband is like that, too much highs and very fast down/up speed.

Main question is, are you shure you broadcast at max 75khz ?
50Khz.... Europe...if you mean pre-emphasis.
Page 64 of 99 All times are UTC+02:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/