As far as i can hear, letest beta sounds better even without SSB.
I cant use Composite clipper, i need new Cpu
Very good Work Hans
Congrats, happy realease
| Stereo Tool https://forums.stereotool.com/ |
|
| Stereo Tool 7.11 BETA https://forums.stereotool.com/viewtopic.php?t=4746 |
Page 30 of 30 |
| Author: | hvz [ Tue May 07, 2013 12:51 pm ] |
| Post subject: | Re: Stereo Tool 7.11 BETA |
Quote: Testing latest beta, composite clipper on, extra composite 1.05x, strictness 15.
This behavior kinda makes sense. We're using composite clipping, and in some cases the signal fits 'exactly' inside the holes in the RDS/stereo pilot. The MPX peak level isn't higher where this happens, but if you zoom in you can see some weird effects (valleys - so in most places where this happens the MPX level is even lower, not higher).Tested with 15219 Hz tone that Bojcha did yesterday: - Red output bars on / off. - L+R part jumps in spectrum Not sure about the red flashing - but it's rare and doesn't cause any problems, so I'll leave it like this for now. |
|
| Author: | Brian [ Tue May 07, 2013 2:57 pm ] |
| Post subject: | Re: Stereo Tool 7.11 BETA |
I have an update to Cobalt that I'm posting after this reply. It does not need volume adjustment for generic, as it is within 0.25 dB of what is currently built-in. I test with TTDR Offline to get generic in the same target range, then check the web version. I would have been done with this yesterday, but there were some power outages. In fact, right now, I hear thunder. On another note, I have been going on a semi-sorta "interview". There is not a position at the moment, but they're thinking about it. Part-time, but something is better than nothing, and it is always easier to find a job if you already have a job. |
|
| Author: | Chris [ Tue May 07, 2013 4:16 pm ] |
| Post subject: | Re: Stereo Tool 7.11 BETA |
As far as i can hear, letest beta sounds better even without SSB. I cant use Composite clipper, i need new Cpu Very good Work Hans Congrats, happy realease
|
|
| Author: | bob53bob [ Tue May 07, 2013 5:03 pm ] |
| Post subject: | Re: Stereo Tool 7.11 BETA |
I have a possible problem on this version (I also swapped computers, so I'm not positive this is ST related). When I restart the system, Sound Cards>FM Output>ASIO Override Channel 1 and ASIO Override Channel 2 jump to ASIO Output 5 and ASIO Output 6 every time. I have to manually reset them to ASIO Output 1 and ASIO Output 2 each time in order to keep the FM Output active. The previous computer running an earlier version powered up & worked reliably each time. |
|
| Author: | gpagliaroli [ Tue May 07, 2013 5:14 pm ] |
| Post subject: | Re: Stereo Tool 7.11 BETA |
Quote: Quote: Hans, in the preset GAP_Dominator_v0.3 you incorporated in the Simple Clipper Amplification value is wrong 62 instead of 100%. (if you generate a new release is a new version of the preset)
That's in the Generic version of the preset! Under "Web radio" it's exactly the way you made it... I think the other presets aggregates have the same problem. 
|
|
| Author: | hvz [ Tue May 07, 2013 5:18 pm ] |
| Post subject: | Re: Stereo Tool 7.11 BETA |
Version is released! Will make a new post for it
|
|
| Author: | eldoradofm [ Tue May 07, 2013 7:15 pm ] |
| Post subject: | Re: Stereo Tool 7.11 BETA |
Quote: 28. Fix Stokkemask clipper. --> Done, but has too much effect on highs and stereo separation. Needs to be calibrated, it's probably too strict now.
I hope you can optimize this soon.
|
|
| Author: | hvz [ Tue May 07, 2013 7:37 pm ] |
| Post subject: | Re: Stereo Tool 7.11 BETA |
Me too _ I actually have a new potentially better idea based on the multipath clipper. |
|
| Author: | eldoradofm [ Tue May 07, 2013 8:36 pm ] |
| Post subject: | Re: Stereo Tool 7.11 BETA |
I also did some tests with the multipath clipper, when i have it on 45% it looks kinda right in MPX tool when i look at the stokkemask. |
|
| Page 30 of 30 | All times are UTC+02:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|