Stereo Tool
https://forums.stereotool.com/

Stereo Tool 7.71 BETA
https://forums.stereotool.com/viewtopic.php?t=6087		 Page 17 of 35
Author:  DJ-DOGGY [ Fri Jul 24, 2015 3:38 pm ]
Post subject:  Re: Stereo Tool 7.71 BETA
Quote:
Doggy, what signal you put on input?
It can be music but for most easy testing , put white noise .
I guess you asking me for the "Ignore highs" problem ?
Author:  DJ-DOGGY [ Fri Jul 24, 2015 3:46 pm ]
Post subject:  Re: Stereo Tool 7.71 BETA
I must report that now "side" of L+R is worse than previous betas.
See the picture.

Please to refer only to the red line , because it is holded for a less than second so the shape can be seen.

Even with Strictness of 20 cannot help to remove the showed (circled) on picture.

Attachments:
SIDE L+R.JPG
SIDE L+R.JPG [ 26.02 KiB | Viewed 4881 times ]
Author:  weskeene [ Fri Jul 24, 2015 3:47 pm ]
Post subject:  Re: Stereo Tool 7.71 BETA
I don't even get it. Aren't we just looking at a 19k pilot? Does this even occur in non-FM modes?
Author:  Bojcha [ Fri Jul 24, 2015 3:51 pm ]
Post subject:  Re: Stereo Tool 7.71 BETA
Quote:
Quote:
Doggy, what signal you put on input?
It can be music but for most easy testing , put white noise .
I guess you asking me for the "Ignore highs" problem ?
Yea but on that image i dont see at all l+r area..
Author:  DJ-DOGGY [ Fri Jul 24, 2015 3:52 pm ]
Post subject:  Re: Stereo Tool 7.71 BETA
Quote:
I don't even get it. Aren't we just looking at a 19k pilot? Does this even occur in non-FM modes?
I again will say : DO NOT look at the pilot ! LOOK AT the right side of L+R signal ! There is "side effect" that NOT exist in the beginning of developing this 7.71 version , neither any old versions . Now get it ?
Author:  DJ-DOGGY [ Fri Jul 24, 2015 3:54 pm ]
Post subject:  Re: Stereo Tool 7.71 BETA
Quote:
Quote:
Quote:
Doggy, what signal you put on input?
It can be music but for most easy testing , put white noise .
I guess you asking me for the "Ignore highs" problem ?
Yea but on that image i dont see at all l+r area..
Look at the last image . You don`t need whole L+R . You need only to see the shape of the end of L+R. I`ll edit the picture and circle the zone .
Author:  weskeene [ Fri Jul 24, 2015 3:56 pm ]
Post subject:  Re: Stereo Tool 7.71 BETA
Yes, please circle what you're worried about. From your explanation, I guess you're worried about that upslope around 24k? Also, what is your lowpass at right now?
Author:  DJ-DOGGY [ Fri Jul 24, 2015 3:59 pm ]
Post subject:  Re: Stereo Tool 7.71 BETA
Quote:
Yes, please circle what you're worried about. From your explanation, I guess you're worried about that upslope around 24k? Also, what is your lowpass at right now?

My worry is at the cut of the lowpass . I already circle it . Refresh page and see.
Yes it`s the upslope but not at 24k. Filter is at default for FM 15000 Hz
This is caused by new modifications of Advanced clipper . It allows a little distort and this is the effect. I can show you old version that NOT allow this and this effect is "zero"

This is NOT caused by the lowpass itself - TESTED!
Author:  DJ-DOGGY [ Fri Jul 24, 2015 4:10 pm ]
Post subject:  Re: Stereo Tool 7.71 BETA
See the difference ?

This is with Advanced clipper OFF and only Bandpass active ! Perfect shape, perfect slope

Attachments:
Only Lowpass , Advanced clipper OFF.JPG
Only Lowpass , Advanced clipper OFF.JPG [ 28.62 KiB | Viewed 4880 times ]
Author:  weskeene [ Fri Jul 24, 2015 4:14 pm ]
Post subject:  Re: Stereo Tool 7.71 BETA
At least it's so low that it's inaudible.
Page 17 of 35 All times are UTC+02:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/