Stereo Tool
https://forums.stereotool.com/

Stereo Tool 6.10
https://forums.stereotool.com/viewtopic.php?t=3065		 Page 153 of 213
Author:  eldoradofm [ Fri Aug 26, 2011 12:16 pm ]
Post subject:  Re: Stereo Tool 6.10
Try breakaway and adjust levels and tilt there. If that also gives overshoots you know it's not because of the software.
Author:  VFR750A45 [ Fri Aug 26, 2011 12:26 pm ]
Post subject:  Re: Stereo Tool 6.10
Quote:
VFR750A45: What happens in BETA079 when you do enable adding a DC offset? I'll have to check if this part of the filter is working less good in the new clipper.
Where it is possible to enable adding DC Offset ?
Thanks
Author:  eldoradofm [ Fri Aug 26, 2011 12:28 pm ]
Post subject:  Re: Stereo Tool 6.10
Quote:
Quote:
VFR750A45: What happens in BETA079 when you do enable adding a DC offset? I'll have to check if this part of the filter is working less good in the new clipper.
Where it is possible to enable adding DC Offset ?
Thanks
In loudness:
Checkbox Forcibly remove DC component caused by Loudness (reduces quality!)
Author:  VFR750A45 [ Fri Aug 26, 2011 12:33 pm ]
Post subject:  Re: Stereo Tool 6.10
Quote:
Quote:
Quote:
VFR750A45: What happens in BETA079 when you do enable adding a DC offset? I'll have to check if this part of the filter is working less good in the new clipper.
Where it is possible to enable adding DC Offset ?
Thanks
In loudness:
Checkbox Forcibly remove DC component caused by Loudness (reduces quality!)
ok activate this box remove the DC Offset ?
Why reduces quality ?

i try this yesterday on beta 104 with no success (with a simple audio cable 1,5m)
i try this on beta 79 i would give you the result later

Test will be with the cable RG59 RCA/BNC
Author:  eldoradofm [ Fri Aug 26, 2011 12:35 pm ]
Post subject:  Re: Stereo Tool 6.10
Ok problem is not the cable. Hans can explain why it reduces the quality.
Author:  hvz [ Fri Aug 26, 2011 2:59 pm ]
Post subject:  Re: Stereo Tool 6.10
Quote:
Why reduces quality ?

i try this yesterday on beta 104 with no success (with a simple audio cable 1,5m)
i try this on beta 79 i would give you the result later
This switch makes it impossible to move the DC level if that helps because it makes clipping less aggressive. For example if you have an asymmetrical tone, moving DC will make it more symmetrical. But moving DC can cause some issues.
Author:  Chris [ Fri Aug 26, 2011 3:28 pm ]
Post subject:  Re: Stereo Tool 6.10
Beta 104 needs optimize... i have gaps :/
Author:  Bojcha [ Fri Aug 26, 2011 4:52 pm ]
Post subject:  Re: Stereo Tool 6.10
@ VFR750A45
Problem is your soundcard! Actually more then 2x problem is TWO of that soundcards you are connecting, because all soundcards have TILT on input even Marian Trace Alpha!
You do not do what we say to you. You must set Tilt. I admint that this is bit tricky in StereoTool but try Breakaway.
If you still don't know how to try that, ask! It's simple.

You will have a MPX Link, that's another Tilt problem and it's needed to adjust that again.

@ Chris
What gap ?
Author:  Brian [ Fri Aug 26, 2011 7:02 pm ]
Post subject:  Re: Stereo Tool 6.10
@Bojcha - have you taken a listen to the hypersonic beta preset that I posted? Also, with this newer beta, have you reduced the dirty bass level any?
Author:  Chris [ Fri Aug 26, 2011 8:45 pm ]
Post subject:  Re: Stereo Tool 6.10
@BOJCHA Utilization gaps... 50-60% Cpu. in case you ask me, i have an AMD 2 cpu @ 3.00 Ghz.
Page 153 of 213 All times are UTC+02:00
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/