I usually use 9-10 for asio on Marian, since it's on separate route
| Stereo Tool https://forums.stereotool.com/ |
|
| Marian Trace Alpha Creating Asio Buffer Failed https://forums.stereotool.com/viewtopic.php?t=7094 |
Page 2 of 4 |
| Author: | beej6 [ Wed Nov 04, 2015 5:10 am ] |
| Post subject: | Re: Marian Trace Alpha Creating Asio Buffer Failed |
Analog input only. Sorry, by digital output what I really mean is MPX into an FM transmitter. |
|
| Author: | beej6 [ Thu Nov 05, 2015 8:46 pm ] |
| Post subject: | Re: Marian Trace Alpha Creating Asio Buffer Failed |
It all seems to be running well, meters for both analog and digital input are OK but still no output via RCA/BNC. SHould I try disabling the analog output in favor of FM/digital/MPX only? Does ST ever default to one or the other even if I route the audio differently in the Marian Trace Alpha? |
|
| Author: | hvz [ Fri Nov 06, 2015 1:34 am ] |
| Post subject: | Re: Marian Trace Alpha Creating Asio Buffer Failed |
I am just completely confused now. What is FM/digital/MPX? MPX is almost always analog (only a few transmitters supports MPX over an AES/EBU digital connection, but the Trace Alpha doesn't have AES/EBU so you can't mean that). And how are you routing things in the Trace Alpha? |
|
| Author: | beej6 [ Fri Nov 06, 2015 4:15 am ] |
| Post subject: | Re: Marian Trace Alpha Creating Asio Buffer Failed |
My apologies, Hans, it is my naivete which is confusing you, totally my fault. Yes, I realized today that MPX is analog; the Marian Trace Alpha has two sets of outputs, 1/4 TRS paired for analog, and RCA paired which I have been calling "digital" but really what I mean is different analog/MPX. Again, sorry. I have to go back and look at the MTA hardware to see if all my internal jumper settings are OK, I did NOT change any, assuming that default settings were good enough... Routing: Input from Analog 1-2 Normal Output: Play 1-2 to ASIO Output 1-2 FM Output: Play 1-2 to ASIO Output 3-4 Trace Alpha Outputs: Analog: Play 1-2 S/PDIF Audio: Play 3-4 (analog) |
|
| Author: | beej6 [ Sat Nov 07, 2015 9:30 pm ] |
| Post subject: | Re: Marian Trace Alpha Creating Asio Buffer Failed |
Ah, a big ST thank you to Bob Hawkins who helped me through a major stumbling block: The MTA composite output is via the 1/4" outputs, NOT the RCA outputs as I was expecting. Next challenge will be to improve the deviation - only getting 32Khz on my first (brief) test. Thanks again BOb! |
|
| Author: | Bojcha [ Sun Nov 08, 2015 3:13 am ] |
| Post subject: | Re: Marian Trace Alpha Creating Asio Buffer Failed |
I usually use 9-10 for asio on Marian, since it's on separate route
|
|
| Author: | beej6 [ Sun Nov 08, 2015 5:17 am ] |
| Post subject: | Re: Marian Trace Alpha Creating Asio Buffer Failed |
Interesting - output right? |
|
| Author: | Bojcha [ Sun Nov 08, 2015 3:52 pm ] |
| Post subject: | Re: Marian Trace Alpha Creating Asio Buffer Failed |
http://i.imgur.com/ePFcv0I.png |
|
| Author: | beej6 [ Sun Nov 08, 2015 4:17 pm ] |
| Post subject: | Re: Marian Trace Alpha Creating Asio Buffer Failed |
thanks! It helps me to see others' setups... |
|
| Author: | beej6 [ Mon Nov 16, 2015 3:04 pm ] |
| Post subject: | MTA: FM, and normal output (was Re: Marian Trace Alpha Creating Asio Buffer Failed) |
OK, I've got ST in the airchain (community radio LPFM). Marian Trace Alpha, sending FM MPX via MTA output 2 to transmitter. MTA mixer is input on Analog 1-2 then Play 1-2; output to Analog. Right now, I have the same FM output on MTA output 1 for streaming audio... but haven't quite figured out if/how to send "Normal" Output to output 1 instead (sound is a bit bright, probably the pre-emphasis?) Should I be looking at an ST setting or a mixer setting or both? |
|
| Page 2 of 4 | All times are UTC+02:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|
