Stereo Tool

But if the lower end of the Limiter threshold is still too high (-12 dB), you should raise all compressor band's thresholds by a certain amount and compensate the less gain reductions with the drive control.
Lower the MB Output to compensate the higher Output Level.
Now there is more Level going into the limiters and you needn't to adjust the thresholds to lower than -12dB.
Regards,
Robert

If i raise all the compressors , i make a more compressed sound , which i don`t want !
So -12 db is not enough to go down and limit that. You understand ? I don`t want to limit at -3 or -6 or -9db . I want to be albe to limit at -16, -18 -20 . So -30 is good enough.
You can`t make compressors(digital) at -26 with 3:1 compression , and to have only -12 limit level ? This limit level will not limit anything.
See, levels in compressor(digital) are down to -35 , right ? Why limiters are only to -12 ?

The Sound doesn't become more compressed if you raise all compressor Band's thresholds.
If you only raise These, the compression becomes lower cause of the higher thresholds.
Compensate this with Drive and Output and the compression and the Sound is exactly the same.
But the limiters are feed with higher Levels so more limiter's gain reduction occurs - like you want.

This all is only a Kind of "Level- Offset".

The compressor threshold's low end is at -40 i think, you Need These lower values only when you work with very low ratios to get a bit more gain reduction.

Regards,
Robert

On the last few updates, I haven't been able to see the screen, when updating and logging into a particular computer by remote. This is a new problem since the new compressors were introduced. It's only happening on a couple of older Dell's (XP), but I've never had a problem like this previously.

All other programs screen properly. ST shows a blank, off-white screen. The toolbar icon appears, but is also blank

Any ideas?

Screen freezes (white screen) here when clicking on the Singleband GUI,

_________________
The Power of Sound

''Music is a moral law. It gives soul to the universe, wings to the mind, flight to the imagination, and charm and gaiety to life and to everything.'' - Plato

hello i need good fm radio present plase !

ı want to super stereo separation present can you load for me ? you know this machines stereomax like this

i want to feel left and right insturiments sound



https://www.youtube.com/watch?v=NS6aknXJxR4
https://www.youtube.com/watch?v=dca5czX5kAI

Do it yourself . You will greatly feеl when you reach the sound you know from the machines you post.

why did you say like that !! i think this is your job ! now load up for me and be quick

I assume what you mean is exaggerated stereo enhancement. In ST you can achieve this by using the Matrix- Mode in the AGC and by turning up the stereo enhancer.

But more is not always better, less is sometimes more.
Cause too much enhancement has three main disadvantages:
-Your Station will lose covered area cause of increased multipath reception (much energy in the L-R)
-If your listener's receiver switches to mono cause of low RF signal strength the signal becomes quieter and bad sounding cause of interfereces
-even with stereo reception some mid- located instruments and vocals will be moved in the Background and sound reverbed

All this shouldn't be what you want.

And I know the Stereo-Maxx Box: designed to make a huge effect. Even if all 3 knobs are turned to "0", there is an enhancement effect, so be careful.

A trick to find a good enhancement intensity setting, based on my experience, is: When you listen with headphones the only thing what you should hear is a little bit of more "fullness" and/or glitter.
If you hear a different mixdown of the instruments or a bigger difference in the wideness, it is too much!

Believe me/us: Less is more, like in much other points!

In FM Broadcast an important point is Mono- compatibility!

Regards,
Robert

P.S.:
The CRL Stereo Gain Controller does only have 3 steps for the release time. Isn't this too coarse?
If so, just take a 47k- Potentiometer with a serial 10k resistor and replace R212/R85 by this.
So you can adjust the release time continously.
I would prefer this!