Stereo Tool https://forums.stereotool.com/ |
|
ST sound quality problem https://forums.stereotool.com/viewtopic.php?f=26&t=29812 |
Page 1 of 1 |
Author: | Sandor [ Fri Dec 18, 2020 1:59 pm ] |
Post subject: | ST sound quality problem |
Hy everyone! I'm using a Raspberry 3 with St jack + Wolfson audio card. Everything working fine,but only with 48Khz bitrate. I can set till 192Khz,but the sound quality is very bad,only work fine with 48Khz. When I turn off the Stereo tool (bypass) ,on 192Khz the sound quality is perfect again. Looks like ST working normal on 48Khz only. Anybody have idea? Cheers. |
Author: | Sandor [ Wed Dec 23, 2020 6:21 am ] |
Post subject: | Re: ST sound quality problem |
Here is the output spectrum (without audio) with the pilot,from the Cirrus audio card,when I use any sample rate except 48khz. https://i.postimg.cc/63KCB1J6/20201223-061340.png |
Author: | aTom [ Wed Dec 23, 2020 10:57 am ] |
Post subject: | Re: ST sound quality problem |
Hi Sandor, didn't you forget to set the 192kHz sample rate in Stereo Tool? In the config file you can find it as "Sample rate=" - at this case if you don't use GUI. Just set it to "Sample rate=192000" Esetleg beszélhetünk magyarul is, ha úgy egyszerűbb. |
Author: | Sandor [ Wed Dec 23, 2020 11:11 am ] |
Post subject: | Re: ST sound quality problem |
Dear aTom. Yes, I did not forget set the sample to 192 Khz. I can change the sample rate only in Jack settings,in the stereo tool is not available. Szia. Először is köszi a vàlaszt. Az a helyzet,hogy minden sample rate-et próbáltam,sikertelenül. Jó minőségben csak 48khz-en megy. Az összes többin olyan a hang,mintha kb 6khz fölött nem szólalnának meg a hangok. Egyszerűen nincs már ötletem... Esetleg nem tudod le lehet-e tölteni régebbi Tool-t valahonnan? Megpróbálnám másikkal is. Te raspit használsz? https://i.postimg.cc/GmGKDd7F/20201223-140054.jpg |
Author: | aTom [ Wed Dec 23, 2020 2:28 pm ] |
Post subject: | Re: ST sound quality problem |
Nem, én a sima windows változatot használom, így sajnos nem valószínű hogy tudok segíteni, ha raspi specifikus a probléma. Le lehet tölteni régebbi verziókat, a https://www.stereotool.com/download/ oldal alján van hozzá egy útmutató. De gyanítom nem ez lesz a baj. Mi a cél? Gondolom egy FM transmittert meghajtani MPX jellel, különben nem lenne fontos a 192kHz-es mintavételezés. Ha a Jack konfigjában beállítod a 192kHz-et, akkor a Stereo Toolban is jól jelenik meg? |
Author: | Sandor [ Wed Dec 23, 2020 2:49 pm ] |
Post subject: | Re: ST sound quality problem |
Igen,az lenne a cél,hogy a stereo kódolást és az rds-t is a tool végezze. Amikor sample rate-et váltok,változik a toolban is. (A hangminőség is változik,ebből gondolom,hogy "csinál" is valamit.) Próbáltam letölteni régebbi verziót,ahogy írtad,de page not found lett a vége Attól tartok Winnek könnyebb dolgom lenne... |
Author: | aTom [ Wed Dec 23, 2020 3:21 pm ] |
Post subject: | Re: ST sound quality problem |
Igen, ez is tulajdonképpen a javaslatom, hogy amennyiben van rá lehetőség, egy windowsos gépen próbáld meg összerakni a presetet, ami biztosan jól működik. Ha ezek után se megy a pi-n, akkor szinte biztos, hogy valami a konfiggal van, és nem a stereo tool hibája. |
Author: | Sandor [ Wed Dec 23, 2020 3:59 pm ] |
Post subject: | Re: ST sound quality problem |
A preset rendben van,megy raspin is szépen. Jack beállítva 192Khz-re, tool ekkor bypass módban van,ekkor kifogástalan a hang.Kikapcsolom a bypass módot(a tool működik),ekkor 7.5khz fölött nincs audio(megfelezi a 15khz-et valahogy) és a pilot frekvenciát is megfelezi. |
Author: | Sandor [ Sat Jan 30, 2021 8:07 am ] |
Post subject: | Re: ST sound quality problem |
Another problem when I change the sample rate. Sorry for the bad video quality... https://youtu.be/B_m-SfxbTKE |
Page 1 of 1 | All times are UTC+02:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |