Stereo Tool https://forums.stereotool.com/ |
|
Stereo Tool 9.70 https://forums.stereotool.com/viewtopic.php?f=14&t=30553 |
Page 9 of 10 |
Author: | hvz [ Sat May 22, 2021 8:37 pm ] |
Post subject: | Re: Stereo Tool 9.70 |
Quote: Quote:
For those who are responding: Are you using specific settings for block size, or do the defaults work? If you're using specific values, please post them here, so we can see if there's a trend in which values are good or bad.
i strongly believe that the sample block sizes will vary greatly upon the users PC configuration, type of PCI/PCB hardware, CPU type and speed, their configuration of ST and the type of sound cards being used as well as the configuration of them, if applicable.in my case, for my specific configuration, the block settings work the best at their lowest levels (160) for WASPI input and KS output @ 50mS, 48Khz sample rate matched all around, this is allowing windows to "take exclusive control of this device" for the input and output sound cards, internal to the laptop and HDMI external. yes, there is an improvement since block sizes have been added, WASPI and KS usability and stability, and a decrease of latency by a marginal but noticeable amount. im able to do an 8 hour test on ST monday to friday. |
Author: | RodeoJack [ Mon May 24, 2021 5:34 am ] |
Post subject: | Re: Stereo Tool 9.70 |
I'm still having the occasional lockup when running VLC streams. The problem reliably happens if the incoming stream is interrupted, usually due to an internet outage at one end or the other. Hans suggested I make sure I had the current VLC version. I've done that. Running VLC through ST works fine, otherwise. ST restarts without issue, but it has to be done manually. I'm running this configuration through 3 computers. All have the same problem. Now running ST v9.7, though this started with earlier versions. |
Author: | beneyto [ Mon May 24, 2021 7:40 pm ] |
Post subject: | Re: Stereo Tool 9.70 |
Quote:
I'm still having the occasional lockup when running VLC streams.
I have the same problem when try to use a stream for input...
The problem reliably happens if the incoming stream is interrupted, usually due to an internet outage at one end or the other. Hans suggested I make sure I had the current VLC version. I've done that. Running VLC through ST works fine, otherwise. ST restarts without issue, but it has to be done manually. I'm running this configuration through 3 computers. All have the same problem. Now running ST v9.7, though this started with earlier versions. |
Author: | EliteData [ Thu May 27, 2021 8:27 pm ] |
Post subject: | Re: Stereo Tool 9.70 |
i see 64Bit Beta 8 is released, what are the changes ? |
Author: | hvz [ Thu May 27, 2021 10:11 pm ] |
Post subject: | Re: Stereo Tool 9.70 |
Quote:
i see 64Bit Beta 8 is released, what are the changes ?
Nothing, only changes to the MicroMPX backup player and WatchCat (> 4 GB support for WAV files).
|
Author: | Daniel1988 [ Fri May 28, 2021 11:03 am ] |
Post subject: | Re: Stereo Tool 9.70 |
Quote: Quote:
i see 64Bit Beta 8 is released, what are the changes ?
Nothing, only changes to the MicroMPX backup player and WatchCat (> 4 GB support for WAV files).
|
Author: | MrKlorox [ Fri May 28, 2021 3:14 pm ] |
Post subject: | Re: Stereo Tool 9.70 |
Quote: Quote:
i see 64Bit Beta 8 is released, what are the changes ?
Nothing, only changes to the MicroMPX backup player and WatchCat (> 4 GB support for WAV files).
I haven't tried many other permutations yet, to narrow it down. But I noticed it stays "enabled" after changing a CPU/buffer setting. |
Author: | hvz [ Mon May 31, 2021 10:42 am ] |
Post subject: | Re: Stereo Tool 9.70 |
Quote: Quote: Quote:
i see 64Bit Beta 8 is released, what are the changes ?
Nothing, only changes to the MicroMPX backup player and WatchCat (> 4 GB support for WAV files).
I haven't tried many other permutations yet, to narrow it down. But I noticed it stays "enabled" after changing a CPU/buffer setting. |
Author: | MrKlorox [ Mon May 31, 2021 5:03 pm ] | ||
Post subject: | Re: Stereo Tool 9.70 | ||
Quote: Quote:
Beta 8 is the first one I've tried, but it seems the Dehummer breaks output for me. It appears to process everything correctly, according to the scope. However with the LQLL on for monitoring, I hear plenty of "skipping."
I see no problems with it in BETA008. Could it be a CPU load issue? And is this something that didn't happen in older versions? (We have not touched the Dehummer in a long time, so that would be odd).
I haven't tried many other permutations yet, to narrow it down. But I noticed it stays "enabled" after changing a CPU/buffer setting. Here's an error I got while enabling the continuous learning shortly after collecting data during this poor performance mode. Tried raising the core count to no avail. (win 10 64 20h2, 64 bit version of stand alone)
|
Author: | hvz [ Tue Jun 01, 2021 2:16 pm ] |
Post subject: | Re: Stereo Tool 9.70 |
@MrKlorox Found & fixed. Wasn't a new problem though, this must have been there for years... |
Page 9 of 10 | All times are UTC+02:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |