Stereo Tool

Crashes related to VLC input still exist, eg on stream loss, ST needs something inside to isolate from libvlc drops etc..

_________________
Urban Junglist

hi... i installed the new Beta and i have some problems witch exception in processing something ... the 8.0 64bit still works fine thow any ideas ?

Please post the exact message! There is over 8 MB of code so I cannot guess where it comes from without more info... And which version are you using exactly? I guess 64 bit, but stand alone, DSP, VST, GML, Generic, Carbon Coder?

I am having problems getting MB 1 to play well in version 8.10 and in 8.11 BETA. Setting density to 0 the bands bury at or near -18 on almost all songs which dulls the sound so badly it cannot be overcome with EQ. My library is normalized to -23 LUFS, player out into ST set to -10. AGC output is -12 with a ratio of 12:1.

I had to revert back to 8.00 because I could never overcome the issue. Anyone else having this problem with MB 1 levels?

Bug in the web remote control:
Does not work the slider

Confirmed and solved.

Confirmed and solved, drop-down menu's were also broken.

Windows 32 bit:
Windows stand alone: http://www.stereotool.com/download/ster ... r_BETA.exe
Winamp DSP: http://www.stereotool.com/download/dsp_ ... r_BETA.exe
Windows VST 32 bit: http://www.stereotool.com/download/vst_ ... l_BETA.dll

DONE 8.12:
- Problem with Analog compressor on some settings fixed, behavior now same as version 8.00 again.
- Slider in ST web GUI works again.

DONE 8.11:
- Crash when loading Jeroen's Sublime 80's preset (Fixed)
- AGC Window bands different (Fixed)
- Rename Start Ratio back to Ratio, we might not need this after all (?)
- GUI: the small processing time box is always showing 50% usage; on the CPU & latency page correct values are shown though ---> Should show the 1st CPU load from that page.
- GUI: in extreme mode for post-AGC & SB compressors the start ratio box starts on the right edge of the GUI but ends on the left, i.e. you see a part of the box above the peak meters
- SST auto-save settings in the background.

Bugs reported:
- Crash in DSP on first startup. 2nd start was ok.
- Bojcha: 'window' is not implemented well. There is 2 main problems. - Window target is very slow. - Speeds inside window are 0 - should be something like 10x slower then agc speed(s) but not 0.

Later:
- Update website LATER
- CHECK CRASH with VLC - VLC related?? Not seen anymore, later.
- Perform latency measurements
- Web interface export preset
- Generate UIDs and use link
- Password for login?
- Attempt Wes Keene's Feedback mode (see Facebook chat)
- Auto-determine best latency/affinity settings
- New idea: FM stereo trick might reduce MP3 artifacts as well! So add it to streaming output.
- Run as a service
- TODO: Add exception if ignoring too high VST parameter numbers (Audacity bug! -> Was fixed in later Audacity version, never mind).
- Websockets? Later
- However, MediaMonkey was quite insistent I upgrade to the later version 4.1.13.1801, so I did, and now what is happening is the Declipper screen is whited out and can't be configured, though it still works with the last set settings.
- Also when I close MediaMonkey, the Declipper screen hangs (everything else closes), and when I do a forced close, Windows says it's MediaMonkey hanging.
- Still a hack (enabled with a special setting) is needed for some people who want RDS with stereo output... It doesn't make any sense but on some transmitters that apparently works... However I only know of one person who uses this. Not urgent now, this person can use an older version for now.
- Remove inputOldSamplesFixedCopy, should not be needed if I split WAVE from VU meter calculations.
Show MicroMPX block size and quality

I hear bad distortions when AGC window is eg 5dB.

_________________
Urban Junglist

I Also Hear Distortions In the Window Function In AGC Even at 3.4db.