Stereo Tool https://forums.stereotool.com/ |
|
Stereo Tool 9.32 BETA https://forums.stereotool.com/viewtopic.php?f=14&t=26118 |
Page 2 of 17 |
Author: | hvz [ Mon May 13, 2019 1:03 pm ] |
Post subject: | Re: Stereo Tool 9.32 BETA |
Quote: Quote:
Hi, I don't see this here - can you give me more details about your settings? I can't think of any logical reason why one channel could suddenly be silent.
I thought it may have been an ASIO issue but no change if I move FM Output to a non ASIO device.However if I opt to turn off FM Output it immediately restores the right channel. Turn FM Output back on - immediate loss of audio for approx 1-2 seconds and only left channel is present. EDIT: Found if I turn off "Synchronize to input or FM Output" on Normal Output it fixes it and I can run with FM Output ON. It was set to AUTO. Forcing it ON also is the same as AUTO (loss of right channel). Does that make any sense? Ross |
Author: | beneyto [ Mon May 13, 2019 7:02 pm ] |
Post subject: | Re: Stereo Tool 9.32 BETA |
Quote: Quote:
Hi, I don't see this here - can you give me more details about your settings? I can't think of any logical reason why one channel could suddenly be silent.
I thought it may have been an ASIO issue but no change if I move FM Output to a non ASIO device.However if I opt to turn off FM Output it immediately restores the right channel. Turn FM Output back on - immediate loss of audio for approx 1-2 seconds and only left channel is present. EDIT: Found if I turn off "Synchronize to input or FM Output" on Normal Output it fixes it and I can run with FM Output ON. It was set to AUTO. Forcing it ON also is the same as AUTO (loss of right channel). Does that make any sense? Ross |
Author: | hvz [ Mon May 13, 2019 11:57 pm ] |
Post subject: | Re: Stereo Tool 9.32 BETA |
New beta (004) available! Right channel is fixed, and Immersive Bass can be moved to before/between/after multiband compressors. |
Author: | mpx [ Sat May 18, 2019 1:24 pm ] |
Post subject: | Re: Stereo Tool 9.32 BETA |
Immersive Bass level not displayed when moved to any of the 3 multiband options. Sounds like it's still working, although somewhat muddy sounding. |
Author: | hvz [ Sat May 18, 2019 3:12 pm ] |
Post subject: | Re: Stereo Tool 9.32 BETA |
Quote:
Immersive Bass level not displayed when moved to any of the 3 multiband options. Sounds like it's still working, although somewhat muddy sounding.
New version is on its way where that's fixed. But, muddy sounding? Can you describe what you mean? (It might have more or less effect than before because the MB's aren't going over it. But it should not sound different from before.)
|
Author: | hvz [ Sat May 18, 2019 6:49 pm ] |
Post subject: | Re: Stereo Tool 9.32 BETA |
BETA009 is available!
|
Author: | Bojcha [ Sat May 18, 2019 8:56 pm ] |
Post subject: | Re: Stereo Tool 9.32 BETA |
Quote:
BETA009 is available!
wow![*] Highpass filter (phase linear mode) now possible at start of chain ok i hoped for better but it's worse. https://i.imgur.com/x8Q5vF7.png |
Author: | hvz [ Sat May 18, 2019 9:32 pm ] |
Post subject: | Re: Stereo Tool 9.32 BETA |
The filter itself didn't change, but the calculation of the cutoff frequency was wrong (too high). So if you set it to 30 Hz, it was actually already 5 dB down at 30 Hz. Now that's no longer the case. |
Author: | Bojcha [ Sat May 18, 2019 9:38 pm ] |
Post subject: | Re: Stereo Tool 9.32 BETA |
At 30Hz its doing almost nothing and artifacts are even worse even at 46Hz (matching old). |
Author: | livewireaus [ Sun May 19, 2019 11:34 am ] |
Post subject: | Re: Stereo Tool 9.32 BETA |
Quote:
BETA009 is available!
Hi HansIt appears that the audio for Normal Out is currently mono when "Synchronize to input or FM output" is set to AUTO and ON. Regards Ross |
Page 2 of 17 | All times are UTC+02:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |